|
| Status |
Public on Dec 20, 2018 |
| Title |
QSS-S3R |
| Sample type |
genomic |
| |
|
| Channel 1 |
| Source name |
cell culture of strain SSH06
|
| Organism |
Saccharomyces cerevisiae |
| Characteristics |
sample type: diploid strain
strain: W303-1AⅹYJM789
|
| Treatment protocol |
Cells from 5 mL medium were collected by centrifugation (5000 rpm for 5 min) and resuspended in 1 mL YPD (pH 3.5) containing 100 ng/mL α-factor (Sigma). QSS4 cells were incubated in a shaking incubator at 30°C for 2 h to allow most (>95%) cells were synchronized at G1 phase. Zeocin (4 µg/mL) was added into the culture of synchronized cells and the incubation was continued for 1 h before cells harvest. To end synchronization and drug treatment, α-factor and Zeocin were removed by two times of ddH2O washing.
|
| Growth protocol |
QSS4 cell were incubated in 10 mL YPD medium to reach an OD600 of 0.2.
|
| Extracted molecule |
genomic DNA |
| Extraction protocol |
Genomic DNA were prepared by standard procedures (St. Charles et al., 2012)
|
| Label |
cy5
|
| Label protocol |
DNA from these colonies was labeled with Cy5, and mixed with control DNA (DNA from the strain JSC24) labeled with Cy3. The two samples were mixed and competitively hybridized to the SNP microarrays.
|
| |
|
| Channel 2 |
| Source name |
cell culture of JSC24
|
| Organism |
Saccharomyces cerevisiae |
| Characteristics |
strain: JSC24
sample type: diploid strain
|
| Treatment protocol |
Cells from 5 mL medium were collected by centrifugation (5000 rpm for 5 min) and resuspended in 1 mL YPD (pH 3.5) containing 100 ng/mL α-factor (Sigma). QSS4 cells were incubated in a shaking incubator at 30°C for 2 h to allow most (>95%) cells were synchronized at G1 phase. Zeocin (4 µg/mL) was added into the culture of synchronized cells and the incubation was continued for 1 h before cells harvest. To end synchronization and drug treatment, α-factor and Zeocin were removed by two times of ddH2O washing.
|
| Growth protocol |
QSS4 cell were incubated in 10 mL YPD medium to reach an OD600 of 0.2.
|
| Extracted molecule |
genomic DNA |
| Extraction protocol |
Genomic DNA were prepared by standard procedures (St. Charles et al., 2012)
|
| Label |
Cy3
|
| Label protocol |
DNA from these colonies was labeled with Cy5, and mixed with control DNA (DNA from the strain JSC24) labeled with Cy3. The two samples were mixed and competitively hybridized to the SNP microarrays.
|
| |
|
| |
| Hybridization protocol |
The hybridization reactions were prepared using an Agilent Oligo aCGH/ChIP-on-Chip Hybridization kit (5188-5220) following kit instructions. Arrays were incubated for 24 hours at 62°. Following hybridization, the arrays were washed for 5 minutes in Oligo aCGH/ChIP-on-Chip Wash Buffer 1 (Agilent 5188-5221) and 1 minute in Oligo aCGH/ChIP-on-Chip Wash Buffer 2 (Agilent 5188-5222) that was pre-warmed to 37°. The arrays were then scanned at wavelengths of 635 and 532 nm using the GenePix scanner and the GenePix Pro software using settings recommended by the manufacturer.Microarrays could be re-used approximately 4-6 times by removing the hybridized labeled DNA sequences from the oligonucleotides. Microarrays and gasket slides were stripped separately in 1x stripping buffer (10 mM potassium phosphate, pH6.6). The slides were slowly heated to the boiling point in the stripping buffer for 30-45 minutes. After stripping, they were transferred to deionized water, and then slowly removed and stored in a nitrogen cabinet. The gasket slides were centrifuged at 500 rpm to remove excess liquid. Labels on microarrays were removed prior to stripping.
|
| Scan protocol |
The data generated by GenePix Pro were exported as .gpr files and analyzed with a homemade software pipeline. Probes that were flagged by the software were deleted from the analysis.
|
| Data processing |
The data generated by GenePix Pro were exported to text files and analyzed with Microsoft Excel. The 635 nm/532 nm ratio was analyzed for each oligonucleotide. The average value of the median ratios of the control probes was calculated and used to normalize the ratios of the experimental probes to a value of 1 by dividing each probe ratio by the average control probe ratio. The Whole genome arrays were completed with Agilent platform with Design ID Agilent-027438 was used. Sectored colonies were mapped using Agilent platforsm with Design IDs Agilent-031671, which contains probes specific only to chromosome IV, and Agilent-047217, which contains many probes on chromsome IV, but few probes near the telomere and centromere of all chromosomes.
|
| |
|
| Submission date |
Dec 19, 2018 |
| Last update date |
Dec 20, 2018 |
| Contact name |
Daoqiong Zheng |
| E-mail(s) |
zhengdaoqiong@163.com
|
| Phone |
86 571 88206636
|
| Organization name |
College of Life Sciences, Zhejiang University
|
| Department |
Institute of Microbiology
|
| Street address |
866 Yuhangtang Road
|
| City |
Hangzhou |
| State/province |
Zhejiang |
| ZIP/Postal code |
310058 |
| Country |
China |
| |
|
| Platform ID |
GPL20144 |
| Series (1) |
| GSE124107 |
Zeocin induced genomic instaiblity in yeast |
|
